update blog
test serial communication
Thursday, August 9, 2012
Tuesday, August 7, 2012
Twenty-Third Day
I started my day updating blog.
Since the router is not working properly, we restart the router to the manufacturing default setting and setup the router again.
This time we use dynamic IP (DHCP) type internet connection.
The result we obtain is positive since our workgroup enable the access to internet.
New network connection details:
- Description : Broadcam 802.11g Network Adapter
- Physical Address : 00-16-CF-B9-0B-AB
- DHCP Enable : Yes
Since the router is not working properly, we restart the router to the manufacturing default setting and setup the router again.
This time we use dynamic IP (DHCP) type internet connection.
The result we obtain is positive since our workgroup enable the access to internet.
New network connection details:
- Description : Broadcam 802.11g Network Adapter
- Physical Address : 00-16-CF-B9-0B-AB
- DHCP Enable : Yes
Monday, August 6, 2012
Friday, August 3, 2012
Twenty-First Day
Update blog,
Writing in log book,
Meet En. Shahril Izuan, UTeM's lecturer to ask about our ask regarding networking.
Tell him about the failure and problems, ask for advise.
Writing in log book,
Meet En. Shahril Izuan, UTeM's lecturer to ask about our ask regarding networking.
Tell him about the failure and problems, ask for advise.
Thursday, August 2, 2012
Twentieth Day
The router we setup from previous day is not functioning as we desired because anyone of us cannot connect to the internet.
The day before, the router still unable some of us with internet connection although some of us is unfortunate to get the internet access.
So, some troubleshoot is done to find where the problem lies.
We check in the IP address for the router and workgroups and check the setting for the router and see if there anything we can change to repair the condition.
We use prompt to pinging the IP configuration to identify the wireless LAN adapter wireless network connection which connection suffix DNS suffix for:
1- IPv4 address : 192:168:0:103
2- Subnet mask : 255:255:255:0
3- default gateway: 192:168:0:1
We also troubleshoot at network and sharing centre to view the problem and find troubleshooting information.
The result show that the internet is in limited access.
So lastly, we decided to use UTeM SCL network to access the internet since the router still failed to unable us to get access.
Below is the prompt result after we pinging the ip configuration:
The day before, the router still unable some of us with internet connection although some of us is unfortunate to get the internet access.
So, some troubleshoot is done to find where the problem lies.
We check in the IP address for the router and workgroups and check the setting for the router and see if there anything we can change to repair the condition.
We use prompt to pinging the IP configuration to identify the wireless LAN adapter wireless network connection which connection suffix DNS suffix for:
1- IPv4 address : 192:168:0:103
2- Subnet mask : 255:255:255:0
3- default gateway: 192:168:0:1
We also troubleshoot at network and sharing centre to view the problem and find troubleshooting information.
The result show that the internet is in limited access.
So lastly, we decided to use UTeM SCL network to access the internet since the router still failed to unable us to get access.
Below is the prompt result after we pinging the ip configuration:
Wednesday, August 1, 2012
Nineteenth Day
Supervise by miss Sakinah for serial communication task. Serial communication is basically is transssion or transmission of data one bit at a time. It enables different equipment to communicate with their outside world. It is called serial because data bits is send in a serial way over a single line.
Software used for this session is PIC c-compiler, PicKit 2 and PL-2303 Vista Driver Installer.
We test for:
1- Counting,
2- LED on and off,
3- Monitor from keypad,
4- LCD display on and off and
5- Relay on and off.
Flow Chart:
Software used for this session is PIC c-compiler, PicKit 2 and PL-2303 Vista Driver Installer.
We test for:
1- Counting,
2- LED on and off,
3- Monitor from keypad,
4- LCD display on and off and
5- Relay on and off.
Flow Chart:
Subscribe to:
Posts (Atom)